Who needs a solar charge controller?

A charge controller is necessary any time a battery bank will be connected to the direct current (DC) output of solar panels. In most cases, this means a small off-grid setup like solar panels on an RV or cabin. If you’re looking for information on how to use solar and batteries off the grid, you’re in the right place!

There are also charge controllers aimed at providing battery backup for an existing grid-tied solar system that is on the roof of a home or business. This application requires a high-voltage charge controller and usually involves rewiring the system to direct a portion of the solar output through the charge controller.

How does a solar charge controller work?

A solar charge controller is connected between solar panels and batteries to ensure power from the panels reaches the battery safely and effectively. The battery feeds into an inverter that changes the DC power into AC to run appliances (aka “loads”).

The four main functions of a solar charge controller are:

Accept incoming power from solar panels
Control the amount of power sent to the battery
Monitor the voltage of the battery to prevent overcharging
Allow power to flow only from the solar panels to the batteries

As a battery charges, its voltage increases, up to a limit. The battery can be damaged if an additional charge is applied past this limit. Therefore, the ability of a battery to provide or accept power can be measured by its voltage. For example, a typical 12-volt AGM lead-acid battery will show a voltage of 11.8 volts at 10% charged to 12.9 volts at 100% charge.

The main function of a solar charge controller is to ensure the amount of power that is sent to the battery is enough to charge it, but not so much that it increases the battery voltage above a safe level. It does this by reading the voltage of the battery and calculating how much additional energy is required to fully charge the battery.

Another important function of the charge controller is to prevent current from traveling back into the solar panels. When the sun isn’t shining, the solar panels aren’t producing any voltage. Because electricity flows from high voltage to low voltage, the power in the battery would flow into the solar panels if there was nothing in place to stop it. This could potentially cause damage. The charge controller has a diode that allows power to flow in one direction, preventing electricity from feeding back into the panels.

How solar power gets from panels to batteries

As we mentioned above, power flows from high voltage to low. So, to add energy to the battery, the output voltage of a solar panel must always be a little higher than the voltage of the battery it’s charging. Thankfully, solar panels are designed to put out more voltage than a battery needs at any given time.

Here’s an example: Say you have a single 100-watt solar panel and a 12-volt battery. Remember from above that a 12-volt battery is actually able to charge up to about 12.9 volts. 12 volts is what is called its “nominal voltage,” while the actual voltage of the battery depends on how charged it is. It might sink to 11.8 volts at low charge, and 12.9 volts when full.

The 100-watt solar panel can put out a maximum of 18 volts, which is a little too high for the battery to accept safely. Leaving it connected to the battery too long could result in a dangerous situation, eventually causing pressure to build up inside the battery and vent out the side as chemical steam.

You need a charge controller in between the solar panel and the battery to limit the voltage available to the battery. But it’s not just about the voltage – it also has to withstand a certain amount of current (amperage) flowing through it. That’s where the amperage rating of the charge controller comes in.

Charge controller amperage rating

The number of amps of current a charge controller can handle is called its “rating.” Exceeding the amperage rating can cause damage to the wiring within the charge controller. Let’s consider a charge controller rated to handle 30 amps of current. The single 100- watt solar panel described above puts out 5.5 amps of current at 18 volts. That amperage is much lower than the charge controller’s maximum of 30 amps, so the charge controller can easily handle the output of the singular solar panel.

In fact, it could handle the output of multiple solar panels wired in parallel (which increases current output). But there’s an important rule about charge controller ratings to consider: always make sure your charge controller is rated to handle 25% more amps than your solar panels are supposed to put out. That’s because solar panels can exceed their rated current output under especially bright sun, and you don’t want to fry your charge controller on the rare occasion when that happens.

Keeping that rule in mind, the 30-amp charge controller in our example could accept a nominal output of up to 24 amps. You could wire as many as four of those 5.5-amp solar panels in parallel to create a solar array capable of putting out 22 amps, staying under the charge controller’s rating plus the 25% cushion. If you think you might expand the size of your solar array in the future, get a charge controller rated for 50% more amps than your immediate needs.

Matching voltages

Another consideration when choosing a charge controller is the voltage of the battery bank you want to charge. Wiring batteries in series increases the voltage they can deliver and accept. For example, two 12-volt batteries wired in series will operate at 24 nominal volts. There are charge controllers on the market that can pair with battery banks of 12, 24, 36, and 48 volts. You need to make sure the charge controller you purchase can pair with the voltage of the battery bank.

Battery charging stages

There are three stages of charging a battery: bulk, absorption, and float. They correspond to how full the battery is.
Bulk: When a battery charge is low, the charge controller can safely push a lot of energy to it, and the battery fills up with charge very quickly.
Absorption: as the battery nears its full charge (around 90%), the charge controller reduces its current output, and the battery charges more slowly until it’s full.
Float: when the battery is full, the charge controller lowers its output voltage just a bit to maintain the full charge.
Think of it like pouring water from a pitcher into a cup with a very slow leak: when the cup is empty, you start pouring and quickly increase the amount of water being poured until the cup is nearly full. Then you reduce the flow until the cup is full. In order to keep the cup full despite the leak, you pour just a trickle to keep it topped off.
The bulk/absorption/float process was developed for lead-acid deep cycle batteries. Some newer lithium batteries allow for higher current up until they’re quite full, meaning a charge controller paired with a lithium battery can be set to shorten or eliminate the absorption stage.

Common features and settings on a charge controller

The basic features of the simplest PWM charge controller include the ability to set the type of battery and battery bank voltage, and lights indicating the phase of charging (bulk, absorption, and float). More advanced PWM and MPPT models come with a small LCD display for programming and data display, a heat sensor port to monitor battery temperature, and a communications port to connect the charge controller to an external display or computer. The most advanced charge controllers offer Bluetooth connectivity and an app for customizing settings.

Recommended products

There are tons of fine charge controllers available on the market. The cheapest PWM charge controllers can be had for around $15, and are often rebranded versions of the same design. These lack many features but are relatively reliable for how inexpensive they are. More expensive PWM charge controllers built with better quality materials can be had for under $50, while full-featured MPPT charge controllers are priced anywhere from $100 to $200.